Alpha Bridge AXFP-10G-ZR+
Features
- 4 CWDM lanes MUX/DEMUX design.
- Up to 2Gb/s data rate per wavelength.
- QSFP+ MSA compliant.
- IEEE 3ba Electrical Interface.
- Digital diagnostic capabilities.
- Compliant with QDR/DDR Infiniband data rates.
- Up to 150m transmission on OM3 multimode fiber (MMF) or 2km transmission on single mode fiber (SMF).
- Operating case temperature: 0 to 70℃.
- Maximum power consumption 5W.
- LC duplex connector.
Applications
- 40GBASE-LX4 Ethernet Links.
- Infiniband QDR and DDR interconnects.
- Client-side 40G datacom connections.
Absolute Maximum Ratings AXFP-10G-ZR+
Parameter | Symbol | Min | Max | Unit |
Storage Temperature | Ts | -40 | 85 | °C |
Operating Case Temperature | TOP | 0 | 70 | °C |
Power Supply Voltage | Vcc | -0.5 | 3.6 | V |
Relative Humidity (non-condensation) | RH | 0 | 85 | % |
Damage Threshold, each Lane | THd | 4.5 | dBm |
Recommended Operating Conditions AXFP-10G-ZR+
Parameter | Symbol | Min | Typical | Max | Unit |
Operating Case Temperature | TOP | 0 | +70 | °C | |
Power Supply Voltage | Vcc | 3.135 | 3.3 | 3.465 | V |
Data Rate, each Lane | 10.3125 | 11.2 | Gb/s | ||
Control Input Voltage High | 2 | Vcc | V | ||
Control Input Voltage Low | 0 | 0.8 | V | ||
Link Distance with (OM3 MMF) | D_MMF | 150 | m | ||
Link Distance (SMF) | D_SMF | 2 | km |
Electrical Characteristics AXFP-10G-ZR+
Parameter | Symbol | Min | Typical | Max | Unit | Notes |
Power Consumption | 3.5 | W | ||||
Supply Current | Icc | 1.1 | A | |||
Transceiver Power-on Initialization Time | 2000 | ms | 1 |
Notes: Power-on initialization time is the time from when the power supply voltages reach and remain above the minimum recommended operating supply voltages to the time when the module is fully functional.
Optical Characteristics AXFP-10G-ZR+
Parameter | Symbol | Min | Typical | Max | Unit | Notes |
Wavelength assignment | L0 | 1264.5 | 1271 | 1277.5 | nm | |
L1 | 1284.5 | 1291 | 1297.5 | nm | ||
L2 | 1304.5 | 1311 | 1317.5 | nm | ||
L3 | 1324.5 | 1331 | 1337.5 | nm |
Transmitter Electro-optical Characteristics AXFP-10G-ZR+
Parameter | Symbol | Min. | Typ. Max. | Units | Note |
Operating Date Rate | 9.95 | 11.3 | Gbps | ||
Input Reference Clock Rate | Not Required | ||||
Output Optical Power | Pout | 1 | --- 4 | dBm | |
Extinction Ratio | ER | 9 | dB | ||
Center Wavelength | °C | 1530 | 1565 | nm | |
Sidemode Supression ratio | SSRmin | 30 | dB | ||
Relative Intensity Noise | RIN | --- | --- -130 | dB/Hz | |
Output Eye | Compliant with IEEE802.3ae | ||||
Differential Input Voltage | VDIFF | 0.12 | --- | 1.0 | |
Transmit Fault Output-Low | TX_FAULTL | 0.0 | --- | 0.5 | |
Transmit Fault Output-High | TX_FAULTH | 2.4 | --- | Vcc | |
TX_DISABLE Assert Time | t_off | --- | --- | 10 | |
TX_DISABLE Negate Time | t_on | --- | --- | 2 | |
Time to initialize | t_init | --- | --- | 300 | |
Interrupt assert delay | Interrupt _on | --- | --- | 200 | |
Interrupt negate delay | Interrupt_off | --- | --- | 500 | |
P_Down/RST assert delay | P_Down/RST_on | 100 | |||
Mod_NR assert delay | Mod_nr_on | 1 | |||
Mod_NR negate delay | Mod_nr_off | 1 | |||
P-Down reset time | 10 | ||||
RX_LOS assert delay | t_loss_on | 100 |
Note: Average optical power shall be measured using the methods specified in TIA/EIA-455-95.
Receiver Electro-optical Characteristics AXFP-10G-ZR+
Parameter | Symbol | Min. | Typ. | Max. | Units | Note |
Optical Input Power-maximum | PIN | -7 | --- | --- | dBm | BER < 10-12 |
Receiver Sensitivity | PIN | --- | --- | -24 | dBm | BER < 10-12 |
Receiver Sensitivity (OMA) | PIN | --- | --- | -22.1 | dBm | BER < 10-12 |
Operating Center Wavelength | C | 1270 | --- | 1600 | nm | |
Receiver Reflectance | Rrx | 27 | --- | --- | dB | |
Dispersion Panelty | 3 | dB | Up to 80 km | |||
Loss of Signal-Asserted | PA | --- | --- | -30 | dBm | |
Loss of Signal-Deasserted | PD | -22 | --- | --- | dBm | |
Differential Output Voltage | VDIFF | 0.6 | 0.8 | V | ||
TTL Input High Voltage | 2 | Vcc | V | |||
TTL Input Low Voltage | 0 | 0.8 | V | |||
TTL output High Voltage | 2.4 | --- | Vcc | V | ||
TTL output Low Voltage | 0 | --- | 0.4 | V | ||
Receiver Loss of Signal Assert Time tA,RX_LOS --- | --- | 100 | μs | |||
Recover Loss of Signal Assert Time tD,RX_LOS --- | --- | 100 | μs |
Block Diagram of Transceiver
MOD_NR
The Mod_NR is an output pin that when High, indicates that the module has detected a condition that renders transmitter and or receiver data invalid, shall consist of logical OR of the following signals:
- Transmit Signal Conditioner Loss of Lock
- Transmitter Laser Fault
- Receiver Signal Conditioner Loss of Lock
MOD_DESEL
The Mod_DeSel is an input pin. When held Low by the host, the module responds to 2-wire serial communication commands. The Mod_DeSel allows the use of multiple XFP modules on a single 2-wire interface bus. When the Mod_DesSel pin is “High”, the module shall not respond to or acknowledge any 2-wire interface communication from the host.
INTERRUPT
Interrupt is an output pin. When “Low”, indicates possible module operational fault or a status critical to the host system.
TX_DIS
TX_DIS is an input pin. When TX_DIS is asserted High, the XFP module transmitter output must be turned off.
MOD_ABS
Mod_ABS is pulled up to Host_Vcc on the host board and grounded in the XFP module. Mod_ABS is then asserted “High” when the XFP module is physically absent from a host slot.
RX_LOS
The RX_LOS when High indicates insufficient optical power for reliable signal reception.
P_DOWN/RST
This is a multifunction pin for module Power Down and Reset. The P_Down/RST pin must be pulled up to VCC3 in the XFP module.
POWER DOWN FUNCTION
The P_Down pin, when held high by the host, places the module in the standby (Low Power) mode with a maximum power dissipation of 1.5W. This protects hosts which are not capable of cooling higher power modules which may be accidentally inserted.
Optical Receptacle Cleaning Recommendations
All fiber stubs inside the receptacle portions were cleaned before shipment. In the event of contamination of the optical ports, the recommended cleaning process is the use of forced nitrogen. If contamination is thought to have remained, the optical ports can be cleaned using a NTT international Cletop® stick type and HFE7100 cleaning fluid. Before the mating of patch-cord, the fiber end should be cleaned up by using Cletop® cleaning cassette.
Ordering Information AXFP-10G-ZR+
Model Number | Part Number | Reach | Input/Output | Signal Detect | Voltage | Temprature |
XFP-ZR+ | OP7K-SA0-15-C | 25dB | AC/AC | TTL | 3.3V | -5°C to 70°C |