Alpha Bridge AXFP-10G-SR

Features

  • Compliant with XFP-MSA INF-8077i
  • Compliant with 10GFC 1200-MX-SN-I Fiber Channel
    Standard
  • Compliant with IEEE802.3ae 10GBASE-SW/SR Ethernet
    Standard
  • Differential CML inputs and CML outputs
  • Single power supply 3.3V
  • TTL signal detect indicator
  • Hot Pluggable
  • Class 1 laser product complies with EN 60825-1
  • RoHS Compliant

Absolute Maximum Ratings AXFP-10G-SR

Parameter Symbol Min. Max. Units Note
Storage Temperature TS 40 85 C  
Supply Voltage Vcc3 0.5 4.0 V  
Input Voltage VIN 0.5 Vcc V  

Recommended Operating Conditions AXFP-10G-SR

Parameter Symbol Min. Max. Units Note
Case Operating Temperature TC -10 70 °C  
Supply Voltage Vcc3 3.1 3.5 V  
Supply Current Icc3 --- 400 mA  

Diagnostics AXFP-10G-SR

Data Address Parameter Range Accuracy
96-97 Temperature -10 °C to 85 °C ±3°C
100-101 Bias Current 0 to 100mA ±10%
102-103 TX Power -8 to +0dBm ±2dB
104-105 RX Power -15 to +0dBm ±2dB
106-107 Vcc3 Voltage 2.9~3.7 Volts ±3%

Transmitter Electro-optical Characteristics AXFP-10G-SR

Parameter Symbol Min. Typ. Max. Units
Operating Date Rate   9.95   11.3 Gbps
Input Reference Clock Rate       Not required  
Output Optical Power        
(50/125μm fiber, NA=0.20) (62.5/125μm fiber NA=0.275) Pout -7.1 --- -1 dBm
Optical Modulation Amplitude (OMA)   OMA   ---   ---   ---   dBm, "Refer to IEEE 802.3ae Table 52-3"
Extinction Ratio ER 3     dB
Center Wavelength lC 840   860 nm
Spectral Width (RMS) Δl   ---   ---   ---   nm, "Refer to IEEE 802.3ae Table 52-8"
Transmitter and Dispersion Penalty TDP     3.9 dB
Relative Intensity Noise RIN --- --- -128 dB/Hz
Output Eye Compliant with IEEE802.3ae
Differential Input Voltage VDIFF 0.25 --- 1.0 V
TX_DISABLE Assert Time t_off --- --- 10 μs
TX_DISABLE Negate Time t_on --- --- 2 ms
Time to initialize t_init --- --- 300 ms
Interrupt assert delay Interrupt_o ff        
P_Down/RST assert delay P_Down/R ST_on     100 ms
Mod_NR assert delay Mod_nr_o n     1 ms
Mod_NR negate delay Mod_nr_o FF     1 ms
P-Down reset time   10     μs
RX_LOS assert delay t_loss_on     100 μs
RX_LOS negate delay t_loss_oFF     100 μs

Receiver Electro-optical Characteristics AXFP-10G-SR

Parameter Symbol Min. Typ. Max. Units Note
Optical Input Power-maximum PIN -1 --- --- dBm BER < 10-12
Receiver Sensitivity PIN --- --- -9.9 dBm BER < 10-12
Receiver Sensitivity in OMA PIN --- --- -11.1 dBm BER < 10-12
Stress Receiver Sensitivity in OMA PIN --- --- -7.5 dBm BER < 10-12
Operating Center Wavelength lC 840 --- 860 nm  
Optical Return Loss ORL 12 --- --- dB  
Loss of Signal-Asserted PA --- --- -20 dBm  
Loss of Signal-Deasserted PD -12 --- --- dBm  
Differential Output Voltage VDIFF 0.575 --- 0.725 V  
TTL Input High Voltage   2   Vcc V  
TTL Input Low Voltage   0   0.8 V  
TTL output High Voltage   2.4 --- Vcc V  
TTL output Low Voltage   0 --- 0.4 V  
Receiver Loss of Signal Assert Time (off to on) tA,RX_LOS --- --- 100 μs  
Recover Loss of Signal Assert Time (on to off) tD,RX_LOS --- --- 100 μs  
I2C Clock Frequency fSCL     400 kHz  

Pin Descriptions AXFP-10G-SR

Pin Logic Symbol Name/Description Note
1   GND Module Ground 1
2   VEE5 Optional -5.2V Power Supply  
3 LVTTL-I Mod_DeSel Module De-select; When held low allows module to respond to 2-wire serial interface  
4 LVTTL-O   Interrupt Interrupt; Indicates presence of an important condition which can be read over the 2-wire serial interface 2
5 LVTTL-I TX_DIS Transmitter Disable; Turns off transmitter laser output  
6   VCC5 +5V Power Supply  
7   GND Module Ground 1
8   VCC3 +3.3V Power Supply  
9   VCC3 +3.3V Power Supply  
10 LVTTL-I/O SCL 2-Wire Serial Interface Clock 2
11 LVTTL-I/O SDA 2-Wire Serial Interface Data Line 2
12 LVTTL-O Mod_Abs Indicates Module is not present. Grounded in the Module 2
13 LVTTL-O Mod_NR Module Not Ready; Indicating Module Operational Fault 2
14 LVTTL-O RX_LOS Receiver Loss of Signal Indicator 2
15   GND Module Ground 1
16   GND Module Ground 1
17 CML-O RD- Receiver Inverted Data Output  
18 CML-O RD+ Receiver Non-Inverted Data Output  
19   GND Module Ground 1
20   VCC2 +1.8V Power Supply 3
    21     LVTTL-I     P_Down/RST Power down; When high, requires the module to limit power consumption to 1.5W or below, 2-Wire serial interface must be functional in the low power mode.
Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle.
22   VCC2 +1.8V Power Supply 3
23   GND Module Ground 1
24 PECL-I RefCLK+ Not Required  
25 PECL-I RefCLK-
26   GND Module Ground 1
27   GND Module Ground 1
28 CML-I TD- Transmitter Inverted Data Input  
29 CML-I TD+ Transmitter Non-Inverted Data Input  
30   GND Module Ground 1

Ordering Information AXFP-10G-SR

Model Number Part Number Reach Input/Output Signal Detect Voltage Temprature
AXFP-10G-SR OP7K-MX3-85-C 300 m AC/AC TTL 3.3V -10°C to 70°C
DOWNLOAD BROCHURE
Scroll to Top